RPG2X10 | RPG2X12 | RPG2X15: How To Set Up & Use

Introduction

Setting up a PA system can seem overwhelming, but this guide will walk you through step-by-step instructions to get your Rockville PA package system up and running. While this tutorial focuses on the RPG2X12, the same process applies to other Rockville models like the RPG2X10 and RPG2X15.

By following these simple steps, you’ll be ready to use your PA system for live performances, parties, or events.

Step 1: Setting Up the Speaker Stands

Each PA package includes two tripod speaker stands. Setting them up is quick and easy:

1. Loosen the bottom knob on the stand.
2. Expand the legs until they cannot extend any further.
3. Tighten the knob to secure the base.
4. Loosen the top knob to extend the upper pole.
5. Select your desired height using the locking pin (third height is recommended).
6. Insert the locking pin through the hole and tighten the top knob to secure it.
7. Repeat the same steps for the second stand.

Step 2: Mounting the Speakers on the Stands

1. Locate the 35mm speaker stand socket at the bottom of the speaker.
2. Loosen the locking knob by turning it to the left.
3. Align the speaker socket with the top of the stand and place the speaker onto it.
4. Tighten the locking knob by turning it to the right to secure the speaker.
5. Repeat the process for the second speaker.

Step 3: Connecting the Speakers to the Powered Mixer

Since these are passive speakers, they require power from the powered mixer. The package includes two 1/4" speaker cables for this connection.

1. Locate the Speaker Output jack on the back of the powered mixer.
2. Insert one end of a speaker cable into this output.
3. Insert the other end into the speaker’s input jack.
4. Repeat the process for the second speaker.
5. Ensure both connections are secure to avoid signal loss.

Step 4: Powering On the Mixer

Before turning on the system, it’s important to avoid feedback:

1. Turn the master volume all the way down before powering on.
2. Locate the power switch on the back of the mixer and turn it on.
3. The LED display on the front panel should light up, indicating the mixer is on.

Step 5: Connecting and Adjusting a Microphone

The RPG2X12 PA package includes two microphones. Follow these steps to connect and set up a microphone:

1. Plug the female end of the XLR microphone cable into the microphone.
2. Before connecting to the mixer, ensure the microphone volume is turned down.
3. Insert the male end of the XLR cable into an XLR input on Channel 1 or Channel 2.
4. Turn on the microphone and gradually increase the channel volume while speaking into it.
5. Adjust the master volume to the desired level.

Step 6: Connecting an Instrument

For musicians, you can also connect an instrument to the mixer.

1. Plug an instrument cable into the Hi-Z (high impedance) input on any available channel.
2. Adjust the channel volume gradually to avoid distortion.
3. Use the EQ controls (Bass and Treble) to fine-tune your instrument’s sound.

Step 7: Adjusting EQ and Effects

Each channel has Bass and Treble controls, allowing you to adjust the sound to your preference:

• Increase Bass for a deeper, fuller sound.
• Increase Treble for a sharper, clearer tone.

The mixer also features built-in reverb and effects:

1. Adjust the Reverb knob to add an echo effect to vocals or instruments.
2. Use the Effects section to modify the Echo and Delay.
3. Turn the Echo volume up to create an echoing effect.
4. Use the Delay control to set how long the echoes last.

Step 8: Using Phantom Power for Condenser Microphones

If using a condenser microphone, it requires phantom power (48V) to function:

1. Plug in the condenser microphone to an XLR input.
2. Press the 48V Phantom Power button on the mixer.
3. The microphone should now be active.

Note: Dynamic microphones do not require phantom power.

Step 9: Using Bluetooth with the Mixer

The mixer supports Bluetooth streaming, allowing you to play music from your phone:

1. Press the Mode button on the mixer until it displays Bluetooth Disconnected.
2. On your phone, go to Bluetooth settings and search for Rockville.
3. Select the device and wait for the connection confirmation sound.
4. Adjust the MP3 volume knob on the mixer to control the Bluetooth audio level.
5. Play a song to test the Bluetooth connection.

Tip: The volume can also be adjusted using the phone’s volume control.

Step 10: Connecting External Devices

If you want to connect a CD player, MP3 player, or other external audio sources, use the RCA line inputs:

1. Use a 3.5mm to RCA cable for connection.
2. Plug the 3.5mm end into your device and the RCA ends into the Line Inputs.
3. Adjust the Line-In volume knob to control the audio level.

Step 11: Expanding Your Setup with Additional Speakers

If you need to expand your PA system, you can connect additional powered speakers or an amplifier:

1. Locate the 1/4" Line Output on the mixer.
2. Run a 1/4" cable from this output to the Line Input of another powered speaker or amplifier.
3. Adjust volume levels accordingly to balance the system.

Conclusion

Setting up your Rockville PA Package System is a straightforward process that ensures high-quality sound for any event. Whether you’re using it for live performances, speeches, or parties, following these steps will get your system running smoothly.

By understanding how to connect speakers, microphones, instruments, and Bluetooth devices, you can fully utilize your PA system’s capabilities.