GO PARTY ZR10: How To Set Up & Use

Introduction:

This guide will walk you through the complete setup of your Rockville Go Party ZR10 Dual 10” Portable Speaker. Whether you’re hosting a karaoke night, performing live, or just playing music, these easy steps will get you started in no time. No technical experience is required.

What’s Included:

• Go Party ZR10 Speaker
• Wireless Microphone
• Wireless Remote Control
• Power Supply

Requirements:

• AA batteries for the wireless microphone (2x)
• Optional: Guitar, additional microphones, AUX/USB/SD media

Step-by-Step Instructions:

1. Powering the Speaker

• Battery Power: Flip the rear power switch all the way to the right.
• AC Power: Flip the switch all the way to the left using the included power supply (also charges the battery).
• Turn the speaker on using the main power switch.

2. Using the LED Lights

• Press the “Light” button on top of the speaker to cycle through 3 LED modes or turn the lights off.

3. Setting Up the Wireless Microphone

• Unscrew the bottom cap to access the battery compartment.
• Insert 2 AA batteries and reattach the cap.
• Ensure the mic volume slider is all the way down.
• Hold the power button on the mic to turn it on.
• Raise the mic volume slider to start using the mic.
• Note: The microphone comes pre-paired with the speaker and displays battery life, signal strength, and frequency.

4. Connecting Wired Microphones

• Lower the mic volume before connecting.
• Use an XLR to ¼” cable.
  • Plug the XLR end into your mic.
  • Plug the ¼” end into Mic 1 or Mic 2 input.
• Turn up the mic volume slider.
• All mic inputs and the wireless mic share the same volume and echo sliders.

5. Using the Echo Effect

• Adjust the echo slider to add an echo to any connected microphone.

6. Connecting a Guitar

• Use a standard ¼” guitar cable.
  • Plug one end into the guitar and the other into the guitar input on the speaker.
• Raise the guitar volume slider and adjust the volume on the guitar itself.

7. Playing Music via Bluetooth

• Press the “Mode” button until the speaker enters Bluetooth mode.
• On your device, go to Bluetooth settings and select “Go Party ZR10”.
• Once paired, audio will stream wirelessly.
• Use bass, mid, and treble sliders to fine-tune the sound.

8. Playing Music via AUX, USB, or SD Card

• Plug in your source.
• Press “Mode” to switch to Line mode.
• Use the volume dial to control playback volume.
• Use onboard controls for:
  • Play/Pause
  • Next/Previous track
  • Repeat
    • Hold the Repeat button to activate Mic Priority Mode (music lowers when you speak).

9. Using TWS (True Wireless Stereo) Mode

• Power off both speakers first.
• Turn both speakers back on and set them to Bluetooth mode.
• On one speaker, press and hold the Fast Forward button for 5 seconds.
• The master speaker will display "BLUE", and the secondary will display "T-O-T".
• Connect your phone to the master speaker via Bluetooth.
• Enjoy stereo playback with right and left channels split across two speakers.

10. Remote Control Functions

• Use the included remote to:
  • Adjust volume
  • Switch modes
  • Control music playback
  • Access lighting and TWS features

Troubleshooting & FAQs:

Q: My wireless mic isn't working. What should I check?

• Ensure it has fresh AA batteries.
• Confirm the mic is powered on.
• Make sure the mic volume slider on the speaker is raised.

Q: I don’t hear sound from my guitar.

• Verify the guitar is plugged in and powered.
• Check both the guitar’s volume and the speaker’s guitar volume slider.

Q: Can I connect multiple microphones?

• Yes, up to two wired mics plus the wireless mic can be used simultaneously.

Q: How do I know which speaker is the master in TWS mode?

• The master speaker will display “BLUE” on the LCD screen.
• The slave speaker will display “T-O-T”.

Conclusion:

Your Rockville Go Party ZR10 is now ready to bring powerful sound and versatility to any event. Whether you're using a mic, guitar, Bluetooth, or USB/SD playback, this speaker makes setup simple and performance easy.