WB65KLS: How To Install, Connect & Control

Introduction

The Rockville WB65KLS 6.5" Metal Marine LED Wakeboard Speakers are designed for high-quality sound on your boat or off-road vehicle. These speakers feature 360-degree swivel mounts, built-in RGB LED lighting, and a wireless RF remote for light control. This guide will walk you through:

• Mounting the speakers
• Wiring the LED lights
• Connecting the speakers to an amplifier
• Using the wireless remote for light control

Step-by-Step Instructions

1. Unboxing and Understanding the Components

Inside the box, you’ll find:

• Two WB65KLS wakeboard speakers (available in black or silver)
• Four non-slip rubber pads (two with holes, two without)
• Wireless RF remote for controlling the LED lights
• 360-degree swivel mounting brackets
• Wiring harness for power and LED connections

2. Mounting the Speakers

1. Remove the Top of the Mounts
   • Use a 6mm Allen key to remove the bolts securing the top portion of the mount.
   • This will reveal an adjustment bolt inside the mount.
2. Adjust the Speaker Position
   • Use a 10mm Allen key to loosen the swivel adjustment bolt.
   • Rotate the speaker to your desired position, then tighten the bolt to secure it.
3. Install the Non-Slip Rubber Pads
   • Place the rubber pad with the hole inside the bottom mount for a better grip.
   • Place the rubber pad without the hole inside the top mount.
4. Mount the Speakers onto the Bar
   • Position the bottom half of the mount on your bar.
   • Place the top half of the mount over the bar.
   • Insert the bolts back through the mount and tighten them with the 6mm Allen key.
5. Repeat the Process for the Second Speaker
   • Mount the second speaker in the same manner.

3. Wiring the LED Lights

The LED lighting system on the WB65KLS speakers requires a 12V power source.

Option 1: Power LEDs with the Amplifier’s Remote Terminal

• White wire = Positive (+)
• Blue wire = Negative (-)

1. Connect the White wire to the Remote Terminal of the amplifier.
2. Connect the Blue wire to the Ground Terminal of the amplifier.
3. When the amplifier powers on, the LEDs will turn on automatically.

Option 2: Constant LED Power

• White wire = Positive (+)
• Blue wire = Negative (-)

1. Connect the White wire to the 12V Positive Terminal on your battery or power block.
2. Connect the Blue wire to the Ground Terminal.
3. The lights will stay on at all times, regardless of whether the amplifier is powered on.
4. Turn the LEDs off manually using the wireless remote.

Connecting the Two Speakers’ LEDs Together

• Use the included power connector to link the two speakers' LED circuits.
• Align the groove on the connector with the groove on the light input to ensure a secure fit.

4. Controlling the LED Lights with the Wireless Remote

The wireless RF remote allows you to customize the lighting modes.

Basic Controls:

• Power Button → Turns the LEDs ON/OFF.
• Demo Mode → Cycles through Red, Green, and Blue colors.
• Speed Buttons → Adjusts the speed of dynamic light effects.

Available Lighting Modes:

• Standard Color Change Mode → Cycles through primary colors.
• Extended Color Change Mode → Includes additional colors like Yellow, Purple, and Light Blue.
• Strobe Mode → Rapid flashing of different colors.
• Pulse Mode → Smoothly transitions between colors.
• Static Colors → Select from Red, Green, Blue, Yellow, Light Blue, Purple, and White.
• Brightness Controls → Adjusts LED brightness up or down.

5. Connecting the Speakers to an Amplifier

1. Locate the Speaker Wires
   • Red Wire = Positive (+)
   • Black Wire = Negative (-)
2. Connect to the Amplifier
   • Insert the Red wire into the Positive terminal of the amplifier.
   • Insert the Black wire into the Negative terminal of the amplifier.
3. Using Speaker Wire Extensions (If Needed)
   • If the speakers are far from the amplifier, use additional speaker wire to extend the connections.
4. Wiring for a Four-Speaker Setup
   • If using a four-channel amplifier, connect the additional two speakers to the remaining two channels.

6. Playing Music Through the Speakers

1. Power on the amplifier.
2. Pair your phone via Bluetooth (if using a Bluetooth-enabled amplifier).
3. Play a song and enjoy your new wakeboard speakers!

Troubleshooting & FAQs

Q: My LED lights aren’t turning on. What should I do?

• Check that the white wire (positive) and blue wire (ground) are connected correctly.
• Ensure the LED power connector is securely connected.
• Try using the wireless remote to turn the lights on.

Q: Can I use the LED lights without turning on the amplifier?

• Yes! Wire the White wire to a 12V power source, and the LEDs will stay on even when the amp is off.

Q: My lights are flashing out of sync.

• Ensure both speakers are properly connected using the power connector.
• Reset the lights by disconnecting and reconnecting power.

Q: What happens if my remote isn’t responding?

• Ensure the batteries in the remote are fresh.
• Try pointing the remote directly at one of the speakers.

Q: Can I install these speakers on an off-road vehicle?

• Yes! These speakers are marine-rated, meaning they can handle water, dust, and rough conditions.

Conclusion

Setting up your Rockville WB65KLS 6.5" Metal Marine LED Wakeboard Speakers is simple and straightforward. Whether mounting them on a boat, ATV, or Jeep, you’ll enjoy powerful audio performance and customizable LED lighting.