RPG10BT V2: How to Set Up & Use

Introduction

The Rockville RPG10BT V2 10-Inch Powered PA Speakers are perfect for live performances, band rehearsals, DJ setups, houses of worship, karaoke, and more. These speakers are designed for versatility, offering multiple mounting options and excellent sound quality. In this guide, we’ll walk you through the steps to set up your RPG10BT V2 speakers, including connecting microphones, adjusting the sound, and using the Bluetooth and wireless features.

What You’ll Need

• RPG10BT V2 10-Inch Powered PA Speakers
• Power cable (included)
• Wireless remote control (included)
• Microphone (optional)
• Speaker stand (optional)
• XLR cables (optional, for additional gear)
• RCA cables (optional, for additional audio sources)

Step-by-Step Instructions

1. Mount the Speaker on a Stand (Optional)

• Prepare the Stand: Loosen the locking knob on your speaker stand to allow the speaker to slide onto the stand.
• Secure the Speaker: Line up the 35mm pole socket at the bottom of the speaker with the pole of the stand. Tighten the locking knob to secure the speaker in place.

2. Power the Speaker

• Plug in the Power Cable: Insert the female end of the included power cable into the back of the speaker and plug the other end into a power outlet.
• Set the Voltage: Adjust the voltage to 110V (for the U.S.) or 220V (for other regions).
• Turn On the Speaker: Flip the power switch to turn on the speaker.

3. Connect the Microphone

• Microphone Connection: Use an XLR cable to connect the microphone to the XLR mic input on the back of the speaker.
• Adjust the Volume: Set the mic level and master volume to the lowest setting to avoid feedback. Gradually raise the mic level and master volume.
• Test the Microphone: Turn on your microphone, and you should hear your voice through the speaker.

4. Adjust the Sound with the Two-Band EQ

• Treble Adjustment: Use the treble knob to adjust the high frequencies. Turning it up will enhance the high end of your voice or music, and turning it down will reduce it.
• Bass Adjustment: Use the bass knob to adjust the low frequencies. Turning it up will add more bass, and turning it down will reduce the low end.
• Note: The two-band EQ will affect both the microphone and any other audio played through the speaker.

5. Connect Additional Audio Sources

• Line-In via XLR: Connect devices with line-level output (like keyboards or additional speakers) using the line-in XLR input.
• Line-In via RCA: For devices like record players or smartphones, connect them using the RCA inputs.
• Line Level Adjustment: Use the line level knob to control the volume of line-level sources.

6. Set Up True Wireless Stereo (TWS) Mode

• Bluetooth Mode: Press the mode button until the speaker switches to Bluetooth mode.
• Activate TWS: Press and hold the TWS button on one of the speakers for about three seconds. Both speakers will beep and show "left" and "right" on the display when connected.
• Pair with Your Device: On your smartphone or tablet, go to Bluetooth settings and select the device named "Rockville" to pair.
• Adjust MP3 Volume: Raise the MP3 volume knob on both speakers to hear music from your device.

7. Connect via USB/SD Card

• Insert USB/SD Card: Plug in a USB drive or SD card into the speaker to play music.
• Set the Input Mode: Set the input mode to USB or SD to hear the music through the speakers.

8. Connect a Passive Mixer (Optional)

• Use a Passive Mixer: Since these are powered speakers, you should use a passive mixer to avoid damaging the equipment.
• Connect to the Mixer: Plug two XLR cables into the main outputs of the mixer and the line inputs on the speakers.
• Adjust Mixer Settings: Raise the gain and volume on the mixer to send the signal to the speakers.
• Test the Setup: Plug a microphone into the mixer, raise the main left and right faders, and the line level knobs on the speakers. Turn on the microphone to hear it through both speakers.

9. Monitor Peak Levels

• Clip Light: The clip LED light on the back of the speaker will light up when the speaker reaches peak volume, indicating distortion. Adjust the levels to prevent clipping.

10. Control Features with the Remote

• Wireless Remote: Use the included wireless remote to control features like:
  • Volume, Bass, Treble: Adjust sound settings from a distance.
  • Input Selection: Switch between Bluetooth, USB, RCA, or XLR.
  • Playback Controls: Use the previous/rewind, pause/play, and fast forward/skip buttons for music playback.

Conclusion

The Rockville RPG10BT V2 10-Inch Powered PA Speakers are now set up and ready for use. Whether you’re performing live, hosting karaoke, or giving a speech, these speakers provide great sound, wireless stereo capabilities, and versatile connectivity options.