ROCK-STREAM PRO: How To Set Up & Use

Introduction

The Rockville Rockstream Pro Dual Pattern USB LED Microphone is a versatile, high-quality microphone perfect for recording, video conferencing, gaming, and more. This guide will walk you through setting up your microphone, adjusting settings, and troubleshooting any issues.

What’s Included

• Rockstream Pro USB microphone (attached to stand)
• USB-C to USB-A/USB-C cable
• Mic stand adapter
• Rockville iUSB adapter for iPhone/iPad
• Built-in pop filter (attached)

Setting Up the Rockstream Pro Microphone

Adjusting the Microphone Position

• The microphone stand allows you to angle the mic in any direction by loosening the side knobs.
• To remove the microphone from the stand, fully loosen the knobs and detach the mic.
• The microphone can be mounted on different stands using the thread on the bottom or the included mic stand adapter.
• The pop filter helps reduce plosive sounds (P’s, T’s, K’s). It can be removed by sliding it off and reattached by sliding it back on.

Connecting to a Computer

Steps to Connect

1. Route the Cable Properly
   • Feed the included USB cable through the bottom of the stand so it fits into the groove at the base.
2. Plug in the Microphone
   • Connect the USB-C end to the bottom of the microphone.
   • Use either the USB-A or USB-C end to connect to your computer, depending on your available ports.
3. Check for Power
   • The LED light inside the microphone will turn blue, indicating that it is powered on.
4. Enable Monitoring (Optional)
   • Plug your headphones into the headphone jack on the bottom of the microphone.
   • Use the top volume knob to adjust headphone monitoring levels.

Selecting the Correct Input and Output

Windows & Mac Settings

1. Open your Sound Settings.
2. Set both Input and Output to Rockstream Pro.
3. If using a DAW (Digital Audio Workstation) like GarageBand or Audacity, select Rockstream Pro as the input/output device within the software.
4. Verify the signal is detected in the software.

Adjusting Polar Patterns

The Rockstream Pro offers two polar patterns for different recording needs:

• Cardioid Mode (Button UP)
  • Captures sound only from the front of the microphone.
  • Ideal for solo recordings, podcasts, and voiceovers.
• Bi-Directional Mode (Button DOWN)
  • Captures sound from both the front and back of the microphone.
  • Great for interviews or duets.

Using the Mute Function

• Press the mute button to disable the microphone.
• The LED will turn red, indicating mute mode.
• Unmute by pressing the button again, turning the LED back to blue.

Troubleshooting Connection Issues

If your computer does not recognize the microphone:

1. Unplug the microphone, wait 30 seconds, and plug it back in.
2. If that doesn’t work, restart your computer, wait 30 seconds, then reconnect the microphone.

If you are not getting signal:

• Ensure the volume knob on the microphone is turned up.
• Check that the Rockstream Pro is selected as the input device.
• Make sure the microphone is not muted (LED should be blue).

Using the Rockstream Pro with an iPhone or iPad

The Rockstream Pro can be used with an iPhone or iPad using the Rockville iUSB USB-A to Lightning Adapter.

Steps to Connect:

1. Plug the Lightning end of the iUSB adapter into your iPhone/iPad.
2. Connect the USB-A end of the microphone cable into the adapter.
3. The microphone’s LED will turn blue, indicating it is powered on.
4. Open any recording or video app and start recording.

Note: The Rockstream Pro will replace the iPhone/iPad’s built-in microphone for better sound quality.

Monitoring Audio Levels

• If the LED turns red, the input volume is too high. Lower the input gain in your recording software.

Conclusion

The Rockville Rockstream Pro Dual Pattern USB LED Microphone is a powerful tool for content creators, musicians, and professionals. Whether you’re recording, streaming, or video chatting, it offers high-quality sound with versatile features.