WET ARRAY 5: How To Set Up The Swivel Bracket

Introduction

The Rockville Wet Array 5 Speaker is a weather-resistant IP55-rated speaker that can be mounted on a wall or ceiling using either the built-in picture frame brackets or the included swivel mount. In this guide, we’ll walk through:

• Using the built-in picture frame brackets
• Mounting the swivel bracket for more flexibility
• Securing the speaker for safety
• Adjusting the vertical and horizontal angles

Step 1: Using the Built-in Picture Frame Brackets (Optional)

The Wet Array 5 Speaker includes two picture frame brackets on the back, allowing you to mount the speaker horizontally or vertically.

How to Mount Using Picture Frame Brackets

1. Choose your mounting location (wall or ceiling).
2. Mark the position for the top and bottom brackets.
3. Drill holes and insert 4-inch or 5-inch drywall anchors.
4. Insert screws into the wall, leaving enough space for the brackets to slide in.
5. Hang the speaker like a picture frame.

Note: The speaker terminals are encased in a thick protective cover, so using 4-inch or 5-inch screws ensures they clear the back.

While this method works well for fixed installations, the swivel mount provides more flexibility for adjusting the speaker’s direction.

Step 2: Using the Swivel Mount (Recommended)

The included swivel mount allows for precise positioning and angle adjustments.

What’s Included in the Swivel Mount Kit?

• Horizontal base plate (attaches to the wall)
• Vertical swivel mount (attaches to the speaker)
• Various screws for assembly

Additional Tools Needed

Phillips screwdriver
Phillips screw gun
Wall anchors and screws (recommended: ¼-inch anchor system for drywall installation)

Step 3: Preparing the Speaker for Mounting

Before mounting the speaker, you need to attach the vertical swivel mount to the back of the speaker.

Attaching the Vertical Swivel Mount

1. Locate the four screws on the back of the speaker.
2. Remove these screws using a Phillips screwdriver (keep the plastic washers attached).
3. Align the vertical mount with the screw holes on the speaker.
4. Reattach the screws to secure the vertical mount.

Now, the speaker is ready to attach to the horizontal base plate.

Step 4: Mounting the Horizontal Base Plate to the Wall

1. Hold the base plate against the wall at the desired height.
2. Mark the four screw hole positions using a Sharpie or pencil.
3. Drill holes at the marked spots and insert ¼-inch anchors.
4. Check alignment by holding the base plate up to the anchors.
5. Secure the base plate to the wall using screws.

Once the base plate is secured, you can attach the speaker mount to the base plate.

Step 5: Securing the Speaker and Safety Cable

1. Slide the vertical mount into the base plate.
2. Attach the safety cable:
   • Take the cable end and loop it through a hole in the base plate.
   • Secure it by tightening a screw through the anchor system.

Why use a safety cable?
Prevents the speaker from falling if the mount loosens over time.

Step 6: Adjusting the Speaker’s Position

Vertical Adjustment (Up/Down Tilt)

1. Find the hole on the side of the mount that aligns with your preferred angle.
2. Insert the large bolt through the hole.
3. Tighten the fly nut to secure the angle.

Horizontal Adjustment (Left/Right Rotation)

1. Position the speaker to your desired left/right angle.
2. Insert two screws through the horizontal adjustment holes.
3. Tighten the screws using a screwdriver to lock the position.

Step 7: Making Future Adjustments

If you ever need to change the speaker angle, simply:

• Loosen the fly nut (for vertical adjustments).
• Loosen the horizontal screws (for left/right adjustments).
• Reposition the speaker and tighten the hardware.

Conclusion

Mounting the Rockville Wet Array 5 Speaker with the swivel bracket provides secure installation and adjustable positioning for optimal sound coverage. Whether you’re installing it in a restaurant, bar, patio, or home setup, the IP55 rating ensures reliable indoor and outdoor performance.