WET-44 PRO: How To Set Up, Wire & Install

Introduction

The Rockville WET 44 Pro is a high-performance 70V wall-mount speaker designed for both indoor and outdoor use. Available in black and white, these speakers are ideal for commercial audio setups, restaurants, bars, and multi-zone sound systems. This guide will walk you through the installation, wiring, and setup process for a seamless audio experience.

What’s Included

• Two Rockville WET 44 Pro speakers (pre-attached swivel mounts)
• Eight screws for mounting
• Swivel brackets for flexible positioning

Understanding 70V Speaker Systems

How 70V Systems Work:

• A 70V amplifier allows multiple speakers to be connected while maintaining constant wattage.
• Each speaker can be tapped at a specific wattage, allowing control over power distribution.

Wattage Taps on WET 44 Pro:

• 3.75W
• 7.5W
• 15W
• 30W
• 6Ω (for standard stereo use)

⚠️ Important: If using the 6-ohm setting, avoid parallel wiring multiple speakers, as it may drop impedance too low for most stereo amplifiers.

Step-by-Step Installation Guide

1. Mounting the Speakers

A. Choosing a Mounting Location

• Identify where you want to mount the speakers horizontally or vertically.
• Ensure the tweeter is pointing toward the listening area for optimal sound coverage.

B. Finding Studs or Using Anchors

• If mounting on wooden studs, use a stud finder to locate and secure the brackets directly to the stud.
• If mounting on drywall, use the included wall anchors for stability.

C. Installing the Swivel Mount Brackets

1. Remove the swivel mount from the speaker by unscrewing the knobs on both sides.
2. Align the bracket with the marked spot on the wall.
3. Use a pencil or marker to mark the drill hole positions.
4. Drill holes for screws or anchors.
5. Secure the swivel mount bracket to the wall using the provided screws.

D. Attaching the Speaker to the Mount

1. Line up the speaker with the mounted bracket.
2. Reattach the knobs on both sides of the speaker.
3. Adjust the swivel angle for optimal sound direction.
4. Tighten the knobs to lock the position.

2. Wiring the Speakers

A. Connecting Speaker Wires

• Locate the spring-loaded terminals on the back of the speaker.
• Press down to insert speaker wires:
  • Red wire → Positive (+)
  • Black wire → Negative (-)

B. Setting the Wattage Tap

• Select the appropriate wattage tap based on your amplifier’s power:
  • 3.75W - 30W for 70V amplifiers.
  • 6Ω setting for standard stereo amplifiers.

C. Running Speaker Wires to the Amplifier

• Route the wires neatly along the walls or through the ceiling for a clean installation.
• Connect each speaker wire to the matching positive and negative terminals on the amplifier.

D. Multi-Zone & Parallel Wiring (Optional)

• Multi-zone amps allow independent volume control for different rooms.
• For parallel wiring, connect multiple speakers in sequence (red to red, black to black).

3. Powering and Adjusting the System

A. Setting Up the Amplifier

1. Turn on the amplifier.
2. Raise the volume for the speaker zone.
3. Raise the master volume.
4. Adjust Bluetooth or MP3 volume if using a digital source.

B. Fine-Tuning Speaker Placement

• Adjust the swivel mount to direct sound where needed.
• Secure the knobs tightly to lock the position.

Troubleshooting & FAQs

Q: How many speakers can I connect to my 70V amplifier?

• This depends on the total wattage of the amp. Example:
  • A 100W amp can support ten speakers at 10W each.

Q: The speaker sound is distorted. How do I fix it?

• Ensure you have not exceeded the amplifier's wattage capacity.
• Check for loose or reversed wiring connections.

Q: Can I mount these speakers outdoors?

• Yes, the WET 44 Pro is weather-resistant and designed for outdoor installations.

Q: Can I use these speakers with a standard home stereo?

• Yes, by setting the speaker to the 6Ω tap. Be careful with parallel wiring, as it may lower the impedance below safe levels.

Conclusion

The Rockville WET 44 Pro speakers are easy to install and ideal for multi-zone audio setups. Whether you're installing them in a restaurant, bar, office, or backyard, following these steps ensures a professional installation with clear and powerful sound.