RG30: How To Set Up & Use

Introduction:
This guide will walk you through the simple and easy process of setting up your Rockville RG30 Boom Arm Microphone Stand. Whether you're mounting a dynamic microphone, a condenser mic with a shock mount, or even a smartphone or tablet, the RG30 offers a clean, adjustable, and space-saving solution for your desktop. No technical experience is needed to follow along.

What’s Included:
After unboxing, you should have the following items:

• RG30 boom arm
• C-clamp (pre-installed)
• Two M8 screws (long and short) for drilling directly into a desk
• Allen key
• Microphone clip (fits most dynamic microphones)
• 6.5 ft. XLR cable

Step-by-Step Instructions

1. Choose Your Mounting Method

You can set up the RG30 in two ways:

• C-Clamp Mount (No drilling):
  • Loosen the clamp, place it on the edge of your desk, and tighten it until secure.
• Direct Desk Mount (Requires drilling):
  • Use the included Allen key to remove the C-clamp portion.
  • Choose between the short or long M8 screw based on your desk’s thickness.
  • Drill a hole into the desk and feed the screw through the hole into the base plate.
  • Tighten using the built-in nut for a flush and stable fit.

2. Insert Boom Arm into Base

• Insert the bottom of the boom arm into the hole on the C-clamp or direct-mount base.
• Press the button on the clamp if you need to remove it later.

3. Attach Your Microphone

• For dynamic microphones:
  • Use the included clip and screw it onto the end of the boom arm.
  • Slide your mic into the clip, ensuring it's facing mouth-level.
• For condenser microphones:
  • Attach a shock mount (e.g., Rockville Rockshock) by screwing it onto the boom arm.
  • Insert your condenser mic securely, making sure the front faces your mouth.
  • Enable phantom power (48V) on your audio interface for condenser mics.

4. Cable Management

• Use the built-in wire clips to hide and route your 6.5 ft. XLR cable along the boom arm.
• Plug the female end into your mic and the male end into your mixer or interface.

5. Add a Pop Filter (Optional but Recommended)

• For dynamic mics: Many already have internal pop filters, but you can use a Rock Pop filter.
• For condenser mics: A pop filter is strongly recommended.
  • Mount it on the small area near the mic, not the arm.
  • Align the filter in front of the mic for optimal performance.

6. Adjust the Boom Arm

• There are three knobs to fine-tune your setup:
  • Top knob: Adjusts mic angle
  • Middle knob: Extends or collapses the arm
  • Bottom knob: Tilts the entire stand forward/back
• The arm freely swivels, allowing flexible mic placement.

Optional Setup: Smartphone/Tablet Mount

Use with IPS22 Mount (Sold Separately)

• Attach the IPS22 to the end of the RG30 arm.
• Loosen the ball joint via the side knob to adjust viewing angle.
• Place your device (phone/tablet) between the adjustable arms.
• Use the built-in clips to run a charging cable neatly through the boom arm.

Troubleshooting & FAQs

Q: My boom arm won’t stay in place after adjusting. What should I do?
A: Make sure all three adjustment knobs are tightened securely once you’ve found your desired position.

Q: My mic clip doesn’t fit.
A: Unscrew the tip of the boom arm to reveal a thinner threading option that may fit your mic or shock mount.

Q: Do I need phantom power?
A: Only if you’re using a condenser microphone. Dynamic mics do not require it.

Q: Can I mount it to a thick desk?
A: Yes. Use the long M8 screw and drill for secure mounting on thicker surfaces.

Conclusion:
The Rockville RG30 Boom Arm Microphone Stand is designed to be easy to install and highly versatile for any workspace. Whether you're using it for podcasting, streaming, or mounting a mobile device, the RG30 offers a clean, customizable setup.