RWM1202VH: How To Set Up & Use

Introduction

The Rockville RWM1202VH VHF Wireless Handheld Microphone System is an excellent choice for live performances, DJ events, karaoke, houses of worship, and more. This guide will walk you through the setup process for connecting the system to either a powered speaker or a powered mixer with passive speakers.

What’s Included:

• Two-channel wireless receiver
• Two wireless handheld microphones
• Two pairs of AA batteries (one pair per microphone)
• Power adapter
• 1/4" (quarter-inch) audio cable

Step-by-Step Setup Instructions

1. Connecting the Receiver to Power

1. Take the female end of the power adapter and plug it into the receiver's power input.
2. Plug the other end into a power outlet.

2. Setting Up the Wireless Microphones

1. Take one of the wireless microphones and unscrew the bottom end cap to reveal the battery compartment.
2. Insert two AA batteries (included) into the microphone, following the polarity markings.
3. Screw the end cap back on.
4. Repeat the process for the second microphone.

3. Connecting to a Powered Speaker

If you are using a powered speaker, follow these steps:

1. Take the included 1/4" audio cable.
2. Plug one end into the "Mix Out" output on the back of the receiver.
3. Plug the other end into the 1/4" microphone input on the powered speaker.
4. Raise the antennas on the receiver for optimal signal reception.
5. Turn on the receiver and the powered speaker.
6. Set the volume knobs on both the receiver and the speaker to the lowest level before testing to avoid feedback.
7. Flip one of the microphones to the ON position.
8. Gradually raise the microphone volume knob on the receiver and the speaker’s volume.
9. You should now hear your voice through the speaker!

🔹 Note: The orange microphone is automatically paired with Mic A, and the blue microphone is automatically paired with Mic B. No manual pairing is required.

4. Connecting to a Powered Mixer with Passive Speakers

If you are using a powered mixer with passive speakers, follow these steps:

1. Take the 1/4" audio cable.
2. Plug one end into the "Mix Out" output on the back of the receiver.
3. Plug the other end into an available channel input on the mixer.
4. Raise the gain on the corresponding mixer channel.
5. Raise the channel fader for that input.
6. Adjust the main left and right faders on the mixer.
7. Turn on the wireless microphone and gradually raise its volume knob on the receiver.
8. You should now hear your voice through the passive speakers!

Benefits of Using a Mixer

Using a mixer with your wireless system allows you to:
Apply EQ adjustments for better vocal clarity.
Use effects (FX) such as reverb or delay.
Control multiple audio sources simultaneously.

5. Wireless Range & Performance

• Indoors: The microphones can be used up to 100-200 feet from the receiver.
• Outdoors: The range is approximately 65-165 feet, depending on environmental factors.
• No Cables Needed: Move freely without being restricted by microphone cables!

Troubleshooting & FAQs

Why isn’t my microphone producing sound?

Ensure the receiver and speaker/mixer are powered on.
Make sure the microphone’s batteries are installed correctly.
Check that the microphone is turned ON.
Ensure the volume on both the receiver and speaker/mixer is turned up.
Make sure the receiver antennas are raised for optimal signal reception.

Can I use both microphones at the same time?

Yes! The two microphones operate on separate channels (Mic A & Mic B), so they work simultaneously without interference.

Can I connect the receiver to a PA system?

Yes! Simply connect the Mix Out output to an available input on your PA system, mixer, or powered speaker.

Conclusion

Setting up your Rockville RWM1202VHVH VHF Wireless Microphone System is quick and easy. Whether you're connecting it to a powered speaker or a mixer with passive speakers, you'll enjoy crystal-clear wireless audio with freedom to move.