RWM2603UR: How To Set Up & Use

Introduction

This guide will walk you through the complete setup of the Rockville RWM2603UR Wireless Rechargeable Mic System. Whether you're a beginner or an experienced user, these easy-to-follow steps will ensure you get the best performance out of your system.

What's Included:

• UHF Receiver
• Two Wireless Rechargeable Microphones
• Two Rechargeable AA Batteries
• Power Cable
• Two UHF Antennas
• Rack Mount Ears (Optional)
• Quarter-Inch Audio Cable

Step-by-Step Setup Instructions

1. Setting Up the UHF Receiver

Powering the Receiver

1. Take the power cable and plug one end into the receiver’s Power In port on the back.
2. Plug the other end into a wall outlet.

Attaching the Antennas

1. Locate the two UHF antennas.
2. Align each antenna with its antenna port on the back of the receiver.
3. Slide it on and turn it clockwise until you hear a click.
4. Adjust the antennas to a vertical position for better signal stability.

Optional: Rack Mounting the Receiver

If you want to mount the receiver into a standard 19-inch, 1U rack space, follow these steps:

1. Remove the screws on both sides of the receiver using a Phillips screwdriver.
2. Attach the rack mount ears by lining them up with the screw holes.
3. Reinsert the screws and tighten them.

2. Installing & Charging the Microphone Batteries

Inserting the Batteries

1. Grab one of the microphones and twist the bottom section counterclockwise to open the battery compartment.
2. Insert the rechargeable AA batteries, making sure to follow the polarity guide.
3. Screw the bottom section back on tightly.

Charging the Microphones

1. Locate the charging ports on the top of the UHF receiver.
2. Insert the microphones into the charging slots, ensuring the connectors align.
3. The LED charge indicator will light up to confirm charging.
4. The receiver charges the microphones whether it is turned on or off.

3. Connecting the System to a Speaker or Mixer

The receiver offers multiple output options: XLR Outputs, Quarter-Inch Outputs, and a Mix Output. Below are two setup options:

Option 1: Using the Mix Output (Single Channel)

1. Use the included quarter-inch cable.
2. Connect one end to the Mix Out port on the receiver.
3. Plug the other end into the input of your powered speaker or mixer.
4. Turn on the system and adjust the volume controls.

Option 2: Using Independent Outputs for Each Mic

To control each microphone separately, follow these steps:

1. Use two XLR or quarter-inch cables.
2. Connect Microphone 1 output to one channel on the powered speaker/mixer.
3. Connect Microphone 2 output to another channel.
4. Adjust the volume of each microphone independently on the speaker or mixer.

4. Adjusting Microphone Levels

• The LCD screen on the receiver shows the frequency assigned to each microphone.
• The volume knobs on the receiver allow you to control each microphone’s output level.
• If connected to a mixer, you can further adjust individual levels using the fader controls.

Troubleshooting & FAQs

Q: My microphone is not turning on. What should I do?

• Make sure the batteries are inserted correctly.
• Check if the microphone needs to be charged.

Q: Why is my microphone cutting out?

• Ensure the antennas are properly installed and positioned upright.
• Avoid interference by keeping the receiver away from other wireless devices.

Q: Can I use regular AA batteries in the microphones?

• No. Only use the included rechargeable AA batteries, as regular batteries cannot be charged through the receiver.

Q: Can I use this system with a mixer?

• Yes! You can connect each microphone individually using the XLR or quarter-inch balanced outputs.

Conclusion

Setting up the Rockville RWM2603UR Wireless Rechargeable Mic System is quick and easy. With its built-in charging system, dual microphone functionality, and flexible output options, it’s perfect for live performances, speeches, and events. Follow these steps, and you’ll be up and running in no time!