FIVE-EYE: How To Set Up, Mount & Use

Introduction

This guide walks you through unboxing, mounting, powering, basic controls, and DMX operation of the Rockville Five-Eye light. The steps are simple and beginner-friendly—no prior lighting or DMX experience required.

You’ll need:

• Included: Five-Eye light, PowerCON power cable, DMX cable, user manual (with three DMX channel guides)
• Optional: DMX controller, lighting clamps, truss or mounting surface

Step-by-Step Instructions

1) Unbox and Identify What’s Included

• Light: Rockville Five-Eye fixture
• Cables: PowerCON power cable (blue locking end) and a DMX cable
• Manual: Includes three DMX guides explaining each channel mode and fader map

2) Choose a Mounting Method

The light ships with an adjustable bracket.

1. Adjust the angle: Loosen the side knobs, set your angle, then tighten.
2. Set on the floor: Use the bracket as a stand on any flat surface.
3. Mount to truss:
   • Use any of the three bracket holes.
   • Attach one or two lighting clamps using the clamp bolt, washer, and nut. Tighten firmly.
   • Hang on truss and secure with the butterfly screws.

Tip: For today’s demo in the video, two end holes were used for two clamps.

3) Power the Light

1. Insert the blue PowerCON end into POWER IN on the light until it clicks, then twist to lock.
2. Plug the other end into AC power. The light powers on automatically.
3. Optional: Use POWER OUT to electrically daisy-chain additional lights on the same truss.

4) DMX Connections (If Using Multiple Lights or a Controller)

• From controller to first light: Controller DMX OUT → DMX IN on Light 1.
• Daisy-chain additional lights: Light 1 DMX OUT → DMX IN on Light 2, and so on.

5) Learn the Back-Panel Controls

• Display: Shows the current mode and address.
• Buttons:
  • MENU: Cycle menus/modes
  • UP/DOWN: Change values
  • ENTER: Save changes

6) Select a DMX Channel Mode

Use MENU until you see one of the following on the display:

• A001 = 7-channel mode (effects-focused)
• H001 = 19-channel mode (effects + per-bulb control)
• h001 = 15-channel mode (per-bulb color control)

Use UP/DOWN to set the DMX address, then ENTER to save.

7) Standalone Operation (No Controller)

A) Auto Programs

• Go to AUTO mode and select from sequences 00–15.
• 15 acts as a color fade.
• Adjust SPEED in the next menu (higher = faster), then ENTER to save.

B) Sound Mode

• Choose one of five sound-active modes.
• The light reacts to loud sounds in the room.

C) Manual Color (RGB Dimmers)

• Use Rxxx, Gxxx, Bxxx menus to set each color level and press ENTER to save.
• Combine values to create a custom color.

8) DMX Control – 7-Channel Mode (A001)

Typical fader layout (consult your controller and the included DMX guide):

• Fader 1: Master Dimmer (raise fully for maximum output)
• Fader 2: Strobe
  • Values 0–4: Engage strobe
  • >4: Increase strobe speed
• Fader 3: Effect Selector
  • Some effects require specific color dimmers to be up
  • Example: For red-based effects, raise Fader 5 (Red), then set Fader 3 to 96–110
  • For multi-color gradient, raise Faders 5/6/7 (R/G/B) and set Fader 3 to 201–215
• Fader 4: Effect Speed (faster as you raise it)
• Faders 5–7: Red, Green, Blue Dimmers

9) DMX Control – 15-Channel Mode (h001)

Control each bulb’s color independently:

• Faders 1–3: Bulb 1 (R, G, B)
• Faders 4–6: Bulb 2 (R, G, B)
• Faders 7–9: Bulb 3 (R, G, B)
• Faders 10–12: Bulb 4 (R, G, B)
• Faders 13–15: Bulb 5 (R, G, B)

10) DMX Control – 19-Channel Mode (H001)

Combines effects and per-bulb control. Use the manual’s 19-channel guide for the full map.

11) Master–Slave Operation (Controller Optional)

Use one light as Master and other lights as Slaves:

1. Cable chain: Master DMX OUT → DMX IN on Slave 1 → continue chaining.
2. Set each Slave to any DMX channel mode (A001/H001/h001).
3. On the Master, select Auto, Sound, or Custom Color.
4. A small dot on the Slave display’s bottom-right flashes to indicate it’s receiving the Master signal.
5. All Slaves will mirror the Master’s mode/color.

Troubleshooting & FAQs

Power & Startup

• Light won’t power on
  • Reinsert the PowerCON until you hear/feel the click, then twist to lock.
  • Verify the AC outlet and cable.
• Fixture reboots when moving cables
  • Ensure the PowerCON is fully locked and strain-relieved.

Mounting & Safety

• Light shifts or sags
  • Tighten the side knobs firmly.
  • Confirm clamp bolts, washers, and nuts are fully tightened.
  • Use properly rated clamps for your truss.

DMX Signal & Addressing

• No DMX response
  • Check cable direction: Controller/Previous Light DMX OUT → DMX IN of the next device.
  • Verify all fixtures are set to the intended mode (A001/H001/h001).
  • In 7-channel setups where all lights act together, give them the same DMX address (e.g., A001).
  • If using a controller, ensure the correct scanner/device is active.
• Only some effects work
  • Many effects require color dimmers to be raised. For example, for red effects, raise Red first.
• Strobe not working or too slow
  • In 7-channel mode, set Fader 2 > 0 to enable, and raise it further for speed.
• Effects are too slow/fast
  • Adjust Speed: Standalone = SPEED menu; DMX = Fader 4.

Sound Mode

• No reaction to music
  • Increase the room volume; ensure you have selected one of the five sound modes.
  • Move the fixture closer to the sound source.

Master–Slave

• Slaves not following the Master
  • Confirm Master DMX OUT → Slave DMX IN cabling order.
  • Slaves must be set to a DMX mode (A001/H001/h001).
  • Look for the flashing dot on Slaves to confirm they’re receiving the Master signal.

Channel Modes (Quick Clarifier)

• 7-Channel (A001): Run global effects across all bulbs.
• 15-Channel (h001): Set individual bulb colors (five bulbs × RGB).
• 19-Channel (H001): Both effects and per-bulb control.

Conclusion

You’ve mounted your Five-Eye, powered it safely, explored standalone modes (Auto, Sound, RGB), and learned how to run it via DMX in 7-, 15-, and 19-channel modes—including Master–Slave chaining. For specific fader values and full channel maps, refer to the DMX guides in your manual.