Rockville MINI RF1 V3 

Par / Wash Light + RF Remote + APP + Wireless DMX

Functions

1. Adjustable Mounting Bracket

2. Mounting Bracket Adjustment Knobs

3. Controls:
   • MENU → Press to switch between modes.
   • UP → Scroll up through values for selected mode.
   • DOWN → Scroll down through values for selected mode.
   • ENTER → Press to access available submenus for the selected mode.

4. LED Display Screen

5. POWER Button

6. Power Input Port

7. Non-Slip Rubber Feet

Remote Control

⚠️If the remote is not working, make sure the units are in RF mode (refer to the RF section) and the screen says "SLAVE." Also, the RF group color/number must match the corresponding RF group/color on the remote. Refer to the RF section for more details and point 1 (below) for RF functions via the remote.

1. RF GROUP → This button changes the RF group of the remote. Keep pressing to cycle through the modes: RED, GREEN, YELLOW, BLUE, and ALL (WHITE). ALL will adjust all 4 groups. The remote also flashes the color of the group you are in when you press the RF button or any other button.

2. ON / OFF → Turns the LEDs on/off. 
   Please note: This button is strictly for the LEDs. The unit will remain on and continue to use battery power. To turn it off, use the POWER button on the unit (Functions section, item 5).

3. COLOR WHEELS → There are eight color wheels, each with four color options. 

   1. COLOR ▲/▼ → Use these  buttons to cycle through the color options in the selected color wheel. Press the BRIGHTNESS buttons (item 4) to adjust the brightness.

4. BRIGHTNESS → Adjust overall brightness in any mode.

5. SOUND MODES → Press these buttons to select the desired sound mode; 1 is color cycle sound mode, 2 is color pulse sound mode, 3 is color strobe sound mode, and 4 is color cycle + pulse + strobe sound mode. 

   2.  SENSITIVITY → Use these blue buttons to adjust the sound mode's sensitivity.

6. SPEED: Changes the speed of the modes (STROBE, PULSE, FADE, and COLOR CYCLE).

7. STROBE: Sets the unit to strobe mode. Use the color wheels to select the desired color, then press the strobe button. Use the SPEED buttons (item 6) to set the strobe speed.

8. PULSE: The unit will pulse through colors. Use the SPEED buttons (item 6) to set the pulse speed.

9. FADE: The unit will fade from one color to next. Use the SPEED buttons (item 6) to set the speed at which the unit will fade between colors.

10. COLOR CYCLE: Cycles through 32 colors. Use the SPEED buttons (item 6) to adjust the speed at which the unit will cycle through colors.

Modes

DMX/SLAVE

This will allow the light to communicate wirelessly with controllers and/or other lights. 

• If not already on the DMX screen, press the MENU button until you see DMX on the top left side of the LED screen.
• When the slave lights connect to the master their Wireless ID will flash, indicating that that are synced.
  

ADD - Address

Here you can set the DMX address and channel mode. 

• The ADD (address) submenu appears first. 
• Use the UP/DOWN buttons to set the DMX address (001 - 512). 
  
• Press the ENTER or MENU buttons to proceed to the next submenu, CH.

CH - Channel

• In the CH (channel) submenu press the UP/DOWN buttons to switch between 6 or 10 channel modes.
  
• Press the MENU button to proceed to the next mode, COLOR.

DMX Controller Functions

When using a DMX controller, use the charts below to reference each channel's function.

6-Channel Mode

10-Channel Mode

Color Mode Menus

Static Colors & Strobe

• From the DMX menu, press the MENU button (twice if the unit is in the ADD submenu) to enter the COLOR menu. 
• Press the ENTER button to switch between the two submenus, SUB and SPEED.
  • Sub: The SUB submenu appears first. Use the UP/DOWN buttons to select one of the 48 preset colors (01 - 48). Press the ENTER or MENU buttons to proceed to the next submenu.
    
     
  • Speed: In the SPEED submenu press the UP/DOWN buttons to set the strobe speed, 00 (off) - 09 (fast). Press the MENU button to proceed to the next mode, JUMP.
    

JUMP - Color Cycle Change

• From the COLOR menu, press the MENU button (twice if the unit is in the SUB submenu) to enter the JUMP menu. In this mode the unit cycles through all colors. 
• Press the UP/DOWN buttons to set the speed, 01 (slow) - 09 (fast). Press the MENU button to proceed to the next mode, FADE.
  

FADE - Color Fade / Pulse Change

• From the JUMP menu, press the MENU button to enter the FADE menu. 
• Press the ENTER button to switch between the two submenus, SUB and SPEED.
  • Sub: The SUB submenu appears first. Use the UP/DOWN buttons to select one of the two settings. SUB 01 will continuously fade from one color to another (color fade). SUB 02 also fades through colors, but fully fades before moving to the next color (color pulse).
    
  • Speed: In the SPEED submenu press the UP/DOWN buttons to set the speed, 01 (slow) - 09 (fast). Press the MENU button to proceed to the next mode, SOUND.
    

SOUND

• From the FADE menu, press the MENU button (twice if the unit is in the SUB submenu) to enter the (sound) menu. 
• Press the ENTER button to switch between the two submenus, SUB and SPEED. 
  • Sub: The SUB submenu appears first.
    
    • Four Sound Modes: Use the UP/DOWN buttons to select one.
      1. Color Cycle Sound Mode → Cycles to a different solid color whenever sound is sensed.
      2. Color Pulse Sound Mode → Pulses to a different color when sound is sensed and if there is no sound or a lull in the sound, the light will fade.
      3. Color Strobe Sound Mode → Strobes a different color when ever sound is sensed.
      4. Color Cycle + Pulse + Strobe Sound Mode → Cycles through the three sound modes.
  • Speed: In the SPEED submenu press the UP/DOWN buttons to set the sensitivity, 01 (least sensitive) to 09 (most sensitive).  Press the MENU button to proceed to the next mode, AP.
    

AP - Phone App

• From the Sound menu, press the MENU button (twice if the unit is in the SUB submenu) to enter the AP - Phone App menu. 
• Use the UP/DOWN buttons to select one of the 4 app groups; AP1, AP2, AP3, or AP4.
  

UID

• While in AP mode, press the ENTER button to see the unit's Unique Identification Number (UID). 
• This is the unit's unique Wifi tag and is used for when synching a light as a master to the app. Each and every unit will have one.

RF

• From the AP menu, press the MENU button to access the RF (RF Group) menu. When the RF function is enabled, you can use the remote to control the units. 

• There are four individual 2.4GHz groups, each represented by a color: rF1 (red), rF2 (green), rF3 (yellow), rF4 (blue).

Remote Only: 

• To use the RF function, first press the ENTER button to switch the units from MASTER mode (image 1) to SLAVE mode (image 2). 

• Use the UP/DOWN buttons to select one of the 4 RF groups. 

  • In this example, the units are set to rF1 (red). This means the same RF GROUP; rF1 (red) should be selected on the remote. 

  • Refer to the remote control functions section and diagrams 3 and 4 below. You can now use the remote to control all the lights.

With Wireless Groups: 

• Set all units to the same wireless group id (refer to Wireless Group ID Settings section). 

  • For this example the wireless group ID is 5 (pink). 

• Select one unit to be the master. Set it to RF mode, in this case rF1. 

• All other units in the group should be set to DMX/SLAVE mode (refer to the DMX/SLAVE section). 

CoL - Custom Color Mixing

• From the AP menu, press the MENU button to enter the CoL (custom color mixing) menu. 
• Press the ENTER button to switch between colors: r (red), G (green), b (blue), u (white), Y (amber), and P (UV), in that order. 
• Use the UP/DOWN buttons to adjust each individual color's brightness, 00 (off, image 1) to 99 (brightest setting, image 2).

• You can adjust an individual color's brightness (image 3) or multiple colors at once. 
  Please note: If you have more than one color "on", it will affect the final color output. For example, if you have red and white on together, the color you see will be a mixture of white and red (image 4). As you add or subtract colors, or adjust the colors' brightness, the hue of the light output will change. Image 4 shows the color output when UV is added to the red and white mix. 

dSP (LCD Screen Time Out Setting)

This will determine how long the LCD menu screen will remain on after after no input from the remote or pressing any of the four panel buttons. This feature is especially useful when truss mounting the units. 

• From the br menu, press the MENU button to enter the dSP (LCD screen time out setting) menu.
  
• Press ENTER, then use the UP/DOWN buttons to cycle through and select one of the time settings; on (always on), 10 (screen remains on for 10 seconds), 20 (screen remains on for 20 seconds), 30 (screen remains on for 30 seconds).

Wireless Group ID Settings

This feature is used for wireless DMX controllers/transmitters and master/slave configuration. To sync with a DMX controller or master light with slave light(s), each needs to be in the same Wireless ID grouping. Multiple different groups can run at once. 

• From the dSP menu, press the MENU button to enter the Wireless Group ID settings menu. 
• Use the UP/DOWN buttons to cycle through the wireless frequency settings; off (wireless option is off), 1 (red wireless frequency group), 2 (green wireless frequency group), 3 (yellow wireless frequency group), 4 (blue wireless frequency group), 5 (purple wireless frequency group), 6 (cyan wireless frequency group), 7 (white wireless frequency group).

Master/Slave

• From the wireless group ID settings menu, press the MENU button to enter the MASTER (Master/Slave) menu. 
• Press the UP/DOWN buttons to turn this function on or off. 
  • When set to off, the unit will not send a signal and the word "MASTER" will not be visible on the screen once you leave the Master/Slave mode menu.
    

Master Mode: When Master mode is turned on, the particular unit will control any units that are within the same wireless group ID. This means that all slave units will respond to any commands sent from the master unit.

Slave Mode: When Master mode is turned off, the unit will not send a signal. When placed in a wireless group ID, the slave unit (or units) will respond to any commands received by the master unit (see Master Mode above).
Please note: The slave unit must be in the same wireless group ID as the master unit. Refer to the Wireless Group ID Settings section on the previous page.