BASS BLASTER 10: How To Set Up & Use

Introduction

Setting up your Rockville Bass Blaster 10 Subwoofer is simple and allows for a variety of configurations to suit your needs, whether it’s for home theater, studio, or live sound setups. This guide will walk you through the essential steps to properly connect and configure your subwoofer, ensuring optimal performance.

1. Initial Setup of the Bass Blaster 10

Step 1: Plug in the Power Cable

• Start by connecting the power cable to the subwoofer. This will provide the necessary power for the sub to function.

Step 2: Turn On the Subwoofer

• Power Button: Press the power switch to turn the subwoofer on.

2. Controls and Features on the Back of the Subwoofer

Step 1: Volume Control

• Use the volume knob to control the overall volume of the subwoofer’s output.

Step 2: Frequency Control (Low Pass Filter)

• The frequency knob controls the low pass filter, allowing you to set the frequency range of sound that the sub will produce.
  • For example, if set to 100 Hz, the sub will only output frequencies below 100 Hz, filtering out higher frequencies.

Step 3: RCA Input and Output

• Line RCA Input: Connect your receiver or other sound source here to send audio to the sub.
• RCA Output: Use this output to connect additional speakers or subwoofers, expanding your setup.

Step 4: Phase Switch

• The phase switch (0° or 180°) adjusts the phase of the subwoofer to ensure it’s in sync with the rest of your setup.
  • If you hear a mismatch or feel that the bass isn't syncing properly with the sound, try flipping the phase switch to correct it.

Step 5: Auto and On Modes

• Auto Mode: The subwoofer powers on only when it receives a signal from the sound source.
• On Mode: The subwoofer remains powered on at all times once the power switch is turned on.

Step 6: High Level Inputs and Outputs

• These high-level input and output terminals allow you to connect the subwoofer to passive speakers in setups like home theaters.

Step 7: LED Control

• LED Switch: Turn the LEDs on to illuminate when music is playing through the subwoofer. Switch to off if you prefer no illumination.

3. Connecting the Bass Blaster 10 to Your Setup

Option 1: Home Theater Setup

• Using RCA:
  • Connect an RCA cable from the sub out on your receiver to the RCA line input on the back of the subwoofer.
• Using High-Level Inputs (if no RCA output is available on the receiver):
  • Use speaker wire to connect your receiver’s speaker terminals to the high-level input on the subwoofer.
  • Then, connect the high-level output from the subwoofer to your main speakers.

Option 2: Studio Setup

• Using an Audio Interface (e.g., Rockville R-Track 2x2):
  • Plug the quarter-inch outputs from your interface into an RCA-to-Quarter Inch cable, and then connect it to the RCA inputs on the subwoofer.
  • Set the frequency knob to the desired range to fine-tune the bass output.

Option 3: Live Sound Setup

• Using a Mixer (e.g., Rock Mix 8):
  • RCA Output: Connect the RCA outputs from your mixer to the RCA input on the subwoofer.
  • Alternatively, use quarter-inch cables by connecting them from the mixer’s control room outputs to the sub’s RCA input.
  • Adjust the volume and frequency on the subwoofer to match your desired sound output.

4. Testing the Setup

• Place the subwoofer on the floor or an optimal spot for your setup.
• Play music or audio from your connected device to ensure that the subwoofer is functioning properly and the bass is synced with the rest of the system.

Conclusion

Setting up your Rockville Bass Blaster 10 Subwoofer is straightforward and flexible, whether for home theater, studio, or live sound use. By following these steps, you’ll be able to fine-tune the subwoofer’s settings and connect it to various devices seamlessly for an optimized listening experience.