R-TRACK 2X2: Guitar, Bass & Synth Recording

Introduction

The Rockville R-Track 2X2 is a versatile USB audio interface designed for recording guitars, basses, synthesizers, and other instruments directly into your DAW (Digital Audio Workstation). With high-Z input capability, you can connect your instrument without the need for a DI box.

This guide will walk you through the step-by-step process of setting up a guitar, bass, or synthesizer with the R-Track 2X2.

Step 1: Connecting a Guitar to the R-Track 2X2

1. Use a Proper Instrument Cable

• Always use a ¼-inch instrument cable to avoid excessive noise in your recording.
• Do not use a speaker cable or line-level cable—they are not designed for guitars.

2. Plug the Cable into the Interface

• Plug one end of the cable into your guitar's output jack.
• Plug the other end into Input 2 on the R-Track 2X2 (designed for instruments).

3. Enable High-Z Mode for Guitars and Basses

• Press the High-Z Button on Input 2.
• This optimizes the input impedance for electric guitars and basses, ensuring clearer signal quality.

Step 2: Adjusting Input Gain & Monitoring

1. Adjust the Gain Knob

• Slowly raise the Gain Knob on Input 2.
• Watch the signal indicator light:
  • Green Light: Signal is coming through at a good level.
  • Red (Peak) Light: Signal is too high—lower the gain.

Tip: If the signal is too loud and distorting, turn down the gain or lower the volume on your guitar.

2. Set Up Monitoring for Recording

• The Monitoring Knob controls what you hear:
  • Direct Mode (Knob Left): Hear the guitar live with zero latency (best for recording).
  • DAW Mode (Knob Right): Hear the processed sound from your DAW (good for mixing).
  • Blend Both: Adjust for your preferred mix between live and DAW audio.

Step 3: Setting Up Your DAW

1. Open Your DAW

• Launch your preferred recording software (Ableton, FL Studio, Pro Tools, Logic, etc.).

2. Create an Audio Track

• Set the input source to "Input 2" (since your guitar is connected to Input 2).

3. Adjust Gain & Test Signal

• Ensure the volume is up on your guitar.
• Play a few notes and watch the input level in your DAW.

4. Start Recording

• Click record and start playing.

Tip: Use an amp simulation plugin in your DAW for realistic guitar tones.

Step 4: Connecting a Bass or Synthesizer

1. Use a ¼-Inch Instrument Cable

• Just like with the guitar, use a ¼-inch instrument cable for bass or synth.

2. Plug into Input 2

• For bass: Press the High-Z Button to optimize the signal.
• For synths: Do NOT press the High-Z Button (synths are line-level and do not need impedance adjustment).

3. Set Up Your DAW

• Create an audio track and set the input to "Input 2".

4. Adjust Gain & Monitor

• Increase the gain gradually.
• Check the signal light to ensure optimal levels.
• Use Direct Monitoring for real-time performance without delay.

5. Record Your Bass or Synth

• Hit record and start playing.

Troubleshooting & FAQs

Q: My guitar signal is too quiet. What should I check?

• Ensure the High-Z button is enabled for guitars or basses.
• Raise the gain knob gradually.
• Increase your guitar’s volume knob.

Q: My signal is too loud and distorted. How do I fix it?

• Lower the gain knob.
• Reduce the guitar's volume.
• Watch the peak indicator light and avoid red clipping.

Q: Do I need an external DI box?

• No—the High-Z input on the R-Track 2X2 acts as a built-in DI for direct recording.

Q: Why is there a delay when I play?

• Switch to Direct Mode (turn the Monitoring Knob left) to remove latency.
• Lower the buffer size in your DAW’s audio settings.

Conclusion

The Rockville R-Track 2X2 makes it simple to record guitars, basses, and synthesizers directly into your computer without the need for additional gear. By following these steps, you can achieve clean and professional recordings in no time.