BATTERY PAR 6RF: How To Set Up & Use

Introduction

This guide will walk you through the setup and operation of the Rockville Battery PAR 6RF, a rechargeable wireless DMX PAR light. We’ll cover charging, mounting options, lighting modes, remote operation, DMX control and master/slave configuration to help you get the most out of your light.

What's Included:
✅Battery PAR 6RF Light (available in black or white)
✅Dual Bracket (for mounting or angling the light)
✅Power Cable (for charging or direct power use)
✅RF Remote (for wireless control; 50-100 ft range)

Setup Guide

A.) Charging the Battery

1. Connect the power cable:
   • Plug the female end of the power cable into the light.
   • Plug the male end into a wall outlet.
2. Monitor the LED indicator:
   • A red LED will indicate charging.
   • A green LED means the battery is fully charged.
3. Charging time:
   • A completely drained battery takes up to 5 hours to fully charge.
   • Once charged, the light can operate for 10 to 15 hours*, depending on the mode and brightness level. 
     • Using lower frequency static colors (e.g. red / green) will drain battery much slower.
     • Using higher frequency static colors (e.g. violet / white) and color-changing modes will drain the battery much faster.

*Battery life expectancy has been adjusted since the creation of this support video.

B.) Attaching the Dual Bracket

1. Align a washer piece with the hole on the inside of the bracket.
2. Insert one of the hand-tightening screws through the hole of the bracket.
3. Align the screw with the mounting hole on the light.
4. Tighten the screw to secure the bracket.
5. Repeat on the other side of the light.

C.) Mounting Options

Wall Washing Setup:

• Using the Rubber Feet: Place the light flush against the wall for an upright beam.
• Using the Dual Bracket: Position the light a few inches away from the wall and angle it upward for a wider wash effect.

Truss / Pole Mount Setup:
To mount the Battery PAR 6RF on a truss or speaker stand pole, you’ll need a lighting clamp (e.g., Rockville LC70: Heavy Duty C-Clamp).

1. Remove the hex-bolt from the lighting clamp.
2. Insert the bolt through the holes on both brackets so the threads are facing outward (away from the light).
3. Align the screw hole on the outside of the clamp with the threads from the bolt.
4. Secure the clamp onto the bracket by tightening the bolt.
5. Loosen the clamp’s butterfly screw until wider than truss / pole diameter.
6. Position the clamp on your truss or speaker stand pole.
7. Tighten the butterfly screw to lock the light in place.

Pro Tip: Since the Battery PAR 6RF is wireless, no power cables are needed when mounting.

Totem Stand & DJ Facade Setup:

• For DJ Booths or Facades (e.g., Rockville RAPFA, RFAA, RockBooth Series): Place the PAR light inside the façade for an illuminated effect.
• For Totem Stands (e.g., Rockville RTP Series): Lift the scrim and place the light in the middle of the stand.

D.) Choosing a Light Mode

Navigating the Light’s Menu:

• Mode Button: Cycles through different modes.
• Up / Down Buttons: Adjust brightness, color, or speed settings.
• Enter Button: Confirms selections.

E.) Using the RF Remote

Setting Up the RF Remote:

1. Turn on the light.
2. Press the Mode button until you reach REN mode.
3. Using the Up /Down buttons; select RN1 or RN2 as the RF Channel.
4. Press Enter to confirm.
5. Use the RF Remote to change colors, brightness, and effects.

1	Brightness ⇧ / ⇩	~Increase / Decrease brightness for static colors. ~Increase / Decrease SOUND mode sensitivity. ~Control effect speed for STROBE, SNAP, FADE and AUTO modes. ~Scroll through 32 preset static colors after pressing Color Wheel button.
2	OFF	Turns LEDs off completely. (Blackout) Please note: This does not power down the light. The POWER switch on the back of the light must be used to fully power off the light (and back on as well).
	ON	Turns LEDS back on after Blackout, and returns them to previous function.
3	Base Colors	6 Buttons for Base Colors; Select Red, Green, Blue, White, Amber or Purple.
3a	Color Wheel	Press Color Wheel button. Then Brightness ⇧ / ⇩ scrolls through 32 color presets.
4	SOUND	Activate sound responsive mode. Brightness ⇧ / ⇩ controls sensitivity.
5	STROBE	Strobe Effect → Brightness ⇧ / ⇩ controls speed.
6	SNAP	Snap / Pulse between colors.  Brightness ⇧ / ⇩ controls speed.
7	FADE	Fades automatically between colors. Brightness ⇧ / ⇩ controls speed.
8	AUTO	Cycles automatically between colors. Brightness ⇧ / ⇩ controls speed.

RF Remote Benefits Over IR Remotes

• Does not require direct line-of-sight to the light.
• Works through walls and objects.
• Has a longer range (50-100 ft or greater) than IR remotes.

F.) DMX Control

Setting Up DMX Control:

1. Press the Mode button until you see Addr.
2. Press Enter to modify the setting.
3. Use the Up / Down buttons to set the DMX address to the address indicated by your DMX controller.
   • Example: A001 for Scanner / Fixture 1
4. Press Enter to save.
5. Press the Mode button until you reach Chnd.
6. Press the Enter button to select Channel mode.
7. Use the Up / Down buttons to choose between 6ch and 10ch.
   • 6-Channel Mode: Controls each color separately.
   • 10-Channel Mode: Includes color control plus effects like strobe and fade.
8. Press Enter to save.

Wireless DMX Setup:
Rockville Wireless DMX Controller or Wireless DMX Transmitter (to connect to any 3-pin DMX output) required for Wireless DMX connection.

• Enable 2.4GHz Wireless DMX:
  1. Press Mode until you reach 2.4G.
  2. Press Enter to modify the setting(if necessary).
  3. Select on and press Enter.
• Set a Wireless DMX ID (1-7):
  1. Press the Mode button until you see id01 ~ id07
  2. Press Enter to modify the setting.
  3. Use the Up / Down buttons to choose a Wireless DMX ID.
     • Example: id01
  4. Press Enter to save.
• Sync the DMX Controller:
  1. Power on your Rockville Wireless DMX Controller or Wireless DMX Transmitter.
  2. Match the Wireless DMX LED Indicator on the controller, or ID Key LED Indicator on the transmitter, with the Wireless DMX ID # on your lights:

     • 1.	Red
       2.	Green
       3.	Yellow
       4.	Blue Dimmer
       5.	Purple
       6.	Turquoise
       7.	White

  3. Press Enter to save.

Wired DMX Setup:
3-Pin DMX Cables (1 per light) required for this.

• Disable 2.4GHz Wireless DMX:
  1. Press Mode until you reach 2.4G.
  2. Press Enter to modify the setting(if necessary).
  3. Select off and press Enter.

DMX Controller Functions:

Pro Tip: You can mix faders 2–7 to create custom colors, then use fader 8 to apply a strobe effect.

G.) Master/Slave Mode
If you want multiple lights to sync together (no DMX controller needed):

Wireless Master/Slave Setup:

• Enable 2.4GHz Wireless DMX on all Battery PAR 6RF Lights:
  1. Press Mode until you reach 2.4G.
  2. Press Enter to modify the setting(if necessary).
  3. Select on and press Enter.
• Set all lights to the same Wireless DMX ID (1-7):
  1. Press Mode until you reach the Wireless DMX ID Menu; Id.01 ~ Id.07
  2. Use the Up / Down buttons to set the Wireless DMX ID to one of the 7.
     • Example: id01
  3. Press Enter to save.
• Choose a Master Light.
  • Use the onboard buttons to set the Master light to a solid color, auto color-changing or sound mode. 
  • All Slave Lights will follow its commands.

Wired Master/Slave Setup:
3-Pin DMX Cable (1 per Slave Light) required for this.

• Using DMX Cable(s):
  1. Connect from the DMX Out of the Master to the DMX In on another Battery PAR 6RF Light; the Slave.
  2. For additional Slaves; connect the DMX Out of the previous connected Slave to another another Battery PAR 6RF.
  3. Repeat the previous step for additional Battery PAR 6RF Slave Lights..
• Set all lights to the same DMX Address and Channel Mode.
  1. Press the Mode button until you see Addr.
  2. Press Enter to modify the setting.
  3. Use the Up / Down buttons to set the DMX address to A001.
  4. Press Enter to save.
  5. Press the Mode button until you reach Chnd.
  6. Press the Enter button to select Channel mode.
  7. Use the Up / Down buttons to select 10ch; for 10-Channel DMX mode.
  8. Press Enter to save.
• Master’s settings will automatically control all connected slave lights.
  • Select any color, mode or function on the Master Light and all Battery PAR 6RF Lights should respond.

Please Note:

• The RF Remote does not work in Master/Slave mode.
• To regain remote functionality, set the lights back to REN mode.

Troubleshooting & FAQs

Q: The light isn't turning on. What should I do?
A: Ensure the battery is charged and the power switch is on. Try plugging in the power cable.

Q: The RF remote isn’t working.
A: Check if the REN mode is set properly on the light, and the remote is set to the correct channel. Both should be on the same RN1 or RN2.

Q: How do I reset the light to factory settings?
A: Go to the settings menu on the light and find the reset option or turn the light off and on while holding the mode button.

Conclusion

With its rechargeable battery, wireless RF Remote and DMX control, the Battery PAR 6RF is a versatile and easy-to-use lighting solution. Whether you're wall washing, truss mounting, up-lighting or creating synchronized light shows, this guide ensures a smooth setup process.