RVSS2-XLR: How To Set Up & Use

Introduction:

In this article, we’ll guide you step-by-step on how to set up your Rockville RVSS2-XLR speaker stands. This tutorial covers everything from unpacking the case, assembling the stands, mounting speakers (both powered and passive), connecting them to your mixer, and repacking everything for storage. No technical experience is needed—just follow these easy steps.

What You’ll Need:

• Rockville RVSS2-XLR speaker stand kit (includes 2 stands + 2 XLR cables)
• Passive or powered mixer
• Powered or passive PA speakers
• XLR or SpeakON speaker cables (depending on setup)

Step-by-Step Instructions

1. Unpacking Your Kit

• Open the included carry case.
• Inside, you’ll find:
  • Two speaker stands
  • Two XLR cables for connecting powered speakers to a passive mixer

2. Setting Up the Speaker Stands

Adjusting the Legs:

1. Loosen the bottom adjustment knob.
2. Push down on the base to spread the legs.
3. Set the width as desired and re-tighten the knob.

Adjusting the Height:

1. Loosen the top knob. The spring-loaded pole may rise slightly—this is normal.
2. Raise the top pole to your preferred height (47" to 79").
3. Insert the included safety pin into the nearest hole below the pole.
4. Tighten the top knob for added security.

Repeat these steps for the second stand.

3. Mounting Your Speakers

For Powered Speakers (e.g., Rockville RPG12):

1. Loosen the locking knob on the speaker's bottom pole mount.
2. Line up the speaker’s pole mount with the stand’s top pole.
3. Slide the speaker onto the pole and tighten the knob to secure it.

For Passive Speakers:

• Follow the same mounting steps as above.
• Ensure the speaker is secured using its built-in locking knob.

4. Connecting Speakers to Your Mixer

Powered Speakers with a Passive Mixer:

1. Use the included XLR cables.
2. Plug the male XLR into the speaker’s line input.
3. Plug the female XLR into the corresponding (L/R) output on your mixer.

Passive Speakers with a Powered Mixer:

1. Use appropriate SpeakON cables.
2. Connect one end to the SpeakON input on the speaker.
3. Connect the other end to the SpeakON output on your mixer.
4. Make sure to match left and right channels correctly.

5. Optional Accessories Setup

Using a DP Mount (Dual Speaker Mount):

• Loosen the side knob on the DP mount.
• Slide the mount onto the top of the stand.
• Tighten the knob to lock it in place.
• Mount two speakers onto the dual sockets.

Using an ACC4 Laptop Tray:

• Mount the accessory on the stand like any speaker.
• Use it to place a laptop or other small equipment on the stand.

6. Packing Up the Stands

Collapsing the Stands:

1. Loosen the bottom knob and pull up the base to retract the legs.
2. Tighten the knob to secure the legs.
3. Loosen the top knob and remove the safety pin.
4. Push the top section down and re-tighten the top knob.

Storing in the Carry Case:

1. Place each stand into its designated slot using the center divider.
2. Use the long Velcro straps for the legs and short ones for the top section.
3. Place the XLR cables in the remaining space.
4. Zip the bag closed.

Troubleshooting & FAQs

Q: The pole rises suddenly when I loosen the height knob—what should I do?
A: This is normal due to the internal spring. Just hold the pole firmly when loosening and adjust as needed.

Q: Can I use passive speakers with a passive mixer?
A: No. You must match passive speakers with powered mixers, and powered speakers with passive mixers.

Q: What if my speaker doesn’t have a locking knob?
A: Most speakers fit snugly onto the pole, but it's always safer to use models with locking knobs for stability.

Q: Can I use different cables than the ones provided?
A: Yes. Use appropriate cables (XLR or SpeakON) depending on your speaker and mixer type.

Conclusion

Setting up your Rockville RVSS2-XLR speaker stands is quick and easy, whether you're using powered or passive speakers. With the included XLR cables and optional accessories like the DP mount and ACC4 tray, you’ll be ready for gigs, rehearsals, or events in no time.