Introduction
This guide will walk you through the setup and operation of your Party Spinner LED Moving Headlight. Whether you want to mount it on a truss, control it with a DMX controller, or use the Master-Slave function, this guide will help you get started.
What’s Included
- Party Spinner LED Moving Headlight
- Wireless Remote
- Power Cable
- Mounting Bracket with Screws
Step-by-Step Setup
1. Mounting the Light
- On a Flat Surface: Place the light on the floor or a totem stand.
- Hanging on a Truss:
- Align the mounting bracket with the screw holes on the bottom of the light.
- Secure the bracket using the included screws with a 5mm Allen key.
2. Turning on the Light and Navigating the Menu
Once powered on, use the buttons under the display:
- Menu: Cycle through different modes.
- Up/Down: Adjust settings.
- Enter: Save settings or access submenus.
3. Understanding the Lighting Modes
| Mode | Function |
|---|---|
| DMX Address Mode | Set a DMX address for DMX control. |
| Channel Mode | Choose between 6-Channel (basic control) or 10-Channel (advanced control). |
| Master-Slave Mode | Assign the light as Master or Slave 1/2 for synchronized operation. |
| Auto Mode | Choose from 9 preset sequences for automatic operation. |
| Sound Mode | Light reacts to sound via the built-in microphone (two sound modes available). |
| LED Mode | Toggle the LED display on/off. |
| Display Mode | Reverse the display orientation. |
| Version Check (VER) | View the software version of the light. |
| Reset Mode | Reset the light to default settings. |
4. Setting Up DMX Control
Using a DMX controller allows customized lighting effects.
A. Choosing DMX Mode
- Select 6-Channel (basic) or 10-Channel (advanced).
- For full control, use 10-Channel Mode.
B. Assigning a DMX Address
- Set the DMX address to A001 (or another address if needed).
- Set all lights to Slave Mode (since the DMX controller acts as the master).
C. Connecting the DMX Controller
- Connect the first light:
- Take a DMX cable.
- Plug the male end into the DMX Out of the controller.
- Plug the other end into the DMX In of the first light.
- Connect additional lights:
- Take another DMX cable.
- Connect DMX Out from the first light to DMX In of the second light.
- Repeat for all additional lights.
- Power on the DMX Controller and activate Scanner 1.
- Reset the Lights (If Needed)
- If the lights don’t respond, go to the Reset Menu on each light and press Enter.
5. DMX Fader Controls in 10-Channel Mode
| Fader | Function |
|---|---|
| Fader 1 | Master Dimmer (brightness control). |
| Fader 2 | Strobe Mode (requires a color to be set). |
| Fader 3 | Pan (horizontal movement, 0° to 540°). |
| Fader 4 | Pan Speed (higher value = slower pan). |
| Fader 5 | Tilt (vertical movement, 0° to 360°). |
| Fader 6 | Tilt Rotate (adjusts tilt speed and direction). |
| Fader 7 | Left Side Color Selection. |
| Fader 8 | Right Side Color Selection. |
| Fader 9 | White Strip Brightness (center strip intensity). |
| Fader 10 | Reset (values 200-209 trigger reset). |
6. Using the Master-Slave Function (Without a DMX Controller)
If you don’t want to use a DMX controller, you can use Master-Slave mode to synchronize multiple lights.
A. Assign Master and Slave Lights
- Choose one light to act as the Master.
- Set all other lights to Slave Mode 1.
B. Connect the Lights with DMX Cables
- Take a DMX cable.
- Connect DMX Out from the Master light to DMX In on the first Slave light.
- Continue this process for all additional Slave lights.
C. Control with the Remote
Using the included wireless remote, you can:
- Turn lights on/off.
- Switch between modes (Auto, Fade, Strobe, Sound, Color).
- Choose preset colors (Red, Green, Blue, White, Amber, Ultraviolet, Orange, Cyan, Pink).
- Adjust brightness.
- Set the DMX address or channel.
Conclusion
Setting up your Party Spinner LED Moving Headlight is quick and easy. Whether you use DMX control or the Master-Slave function, this guide ensures you get the most out of your lighting setup.
Comments
0 comments
Article is closed for comments.