RVMIC4 V2: How To Set Up & Use

Introduction:
This guide will show you how to set up your Rockville RVMIC4 V2 stand with various accessories, including dynamic microphones, condenser microphones, pop filters, smartphone holders, ISO boxes, and boom arms. Follow these simple steps to build a customized setup for your needs. Whether you’re recording in the studio or performing on stage, this guide will walk you through each option to create a well-organized and flexible configuration.

Requirements:

• Rockville RVMIC4 V2 stand
• Mic clip
• Dynamic or condenser microphone
• Mic cable
• Shock mount (for condenser mic)
• Pop filter (optional)
• Smartphone or tablet holder (optional)
• ISO box (optional)
• Boom arm (optional)

Step-by-Step Instructions:

1. Attach the Stand to the Base Plate

• Line up the threading on the bottom of the mic stand with the threading on top of the base plate.
• Screw the stand into the base by twisting to the right until it’s secure.

2. Adjust the Stand Height

• Use the quick release hand clutch to adjust the height of the stand.
• Press down on the clutch, raise or lower the stand, and let go once you’ve set the desired height. The stand will stay in place.

3. Attach the Mic Clip for a Dynamic Microphone

• Line up the threading on the bottom of the mic clip with the threading on top of the stand.
• Screw the mic clip into place.
• Slip your dynamic microphone into the clip, securing it.

4. Switch to 3/8 Threading (Optional)

• If you need to attach different accessories, unscrew the 5/8 threading at the top of the stand to reveal 3/8 threading for compatibility with other mic clips or boom arms.

5. Organize the Mic Cable

• The RVMIC4 V2 comes with a wire clip for organization.
• Plug the mic cable into the microphone, attach the wire clip to the stand, and run the cable through the clip to keep everything neat.

6. Setting Up a Condenser Microphone

• Attach the shock mount for the condenser microphone by screwing it onto the stand’s threading.
• Loosen the shock mount’s knob, lower it to the desired position, and tighten it to lock it in place.
• Pinch the clamps on the shock mount and slide the condenser mic into place, then release the clamps to secure it.

7. Attach a Pop Filter (Optional)

• Loosen the clamp on the pop filter and slip it onto the mic stand.
• Position it high enough so that it covers the microphone, then tighten the clamp to secure it in place.

8. Set Up a Smartphone or Tablet Holder (Optional)

• Line up the threading on the phone/tablet holder with the threading on top of the stand.
• Screw the holder into place.
• Loosen the knob on the side to adjust the angle and position of the holder, then tighten the knob to lock it in place.
• Use the wire clip to keep the charging cable organized.

9. Add an ISO Box (Optional)

• Remove the door from the ISO box for better visibility.
• Unscrew the black attachment piece from the box and line up the opening on the bottom with the threading on top of the stand.
• Once aligned, screw the attachment piece back in to secure the ISO box to the stand.
• Reattach the door and set up the microphone inside the ISO box.

10. Attach a Boom Arm (Optional)

• Unscrew the 5/8 adapter at the top of the stand to reveal 3/8 threading.
• Line up the threading of the boom arm to the stand and screw it on.
• Use the knob at the bottom of the boom arm to lock it in place if it sways.
• Adjust the boom arm’s height and reach using the knobs provided.

Conclusion:
Setting up your Rockville RVMIC4 V2 is straightforward and flexible, allowing you to customize your setup with dynamic microphones, condenser microphones, pop filters, smartphone holders, ISO boxes, and boom arms. Remember to use the wire clip for neat cable management and adjust the stand’s height with the hand clutch for the perfect position.