RWM-ICE: How To Set Up & Use

Introduction

This guide will show you how to set up your Rockville RWM-ICE wireless microphone system for different use cases, whether you're using a powered speaker, mixer, or both. You’ll also learn how to sync and troubleshoot frequencies, ensuring your microphones perform optimally.

Step-by-Step Instructions

1. Unboxing the RWM-ICE

• Inside the protective case, you will find:
  • Two wireless microphones covered in faux diamonds for a stylish performance.
  • A receiver to connect the microphones wirelessly.
  • Antennas to enhance signal strength.
  • Power cable for the receiver.
  • 1/4” cable to connect the receiver to speakers or mixers.
  • Four AA batteries (two per microphone).

2. Setting Up the Receiver and Antennas

• Attach the Antennas:
  • Take each antenna and align the grooves inside the antenna ports on the back of the receiver.
  • Twist the antennas to the right until you hear a click, ensuring they are securely attached.
  • Adjust the antennas to strengthen the signal.
• Connect the Receiver to Your Speaker or Mixer:
  • Use the 1/4" cable to connect the quarter-inch output of the receiver to your mixer or powered speaker.

3. Powering Up the Receiver

• Plug in the power cable to the receiver’s power port and turn on the receiver using the power button.
• The display and volume knobs for each microphone will light up, indicating the receiver is powered on and ready.

4. Frequency Syncing

You can sync your microphones to the receiver either manually or using the auto scan feature.

Manual Frequency Sync

• Select Frequency:
  • On Microphone A, use the up and down buttons to cycle through available frequencies.
  • Once you find a new frequency, press the set button while holding the microphone near the receiver.
  • The microphone display will flash to indicate it’s synced.

Auto Scan Feature

• Auto Scan Sync:
  • Hold the set button until "scan" appears on the receiver’s display.
  • Use the up and down buttons to allow the receiver to automatically find the clearest frequency.
  • Hold the microphone near the receiver, and once the display flashes, the microphone is synced.

5. Setting Up Microphones

• Install the Batteries:
  • Unscrew the bottom cap of the microphone and place the AA batteries inside (positive side facing down).
  • Replace the cap and turn on the microphone by holding the power button. The microphone display will light up.
• Mute and Unmute:
  • Quick press the power button on the microphone to mute it.
  • Press again to unmute.

6. Connecting the Receiver to a Powered Speaker (BPA 10)

1. Connect the 1/4" Cable:
   • Plug one end of the 1/4" cable into the receiver’s quarter-inch output.
   • Plug the other end into the quarter-inch input of the speaker.
2. Power Up:
   • Turn on the speaker and raise the volume knob.
3. Test the Microphone:
   • Raise the volume knob for your microphones on the receiver.
   • Speak into the microphone (e.g., "Check one, two"). Your voice should come through the speaker.

7. Using Bluetooth for Karaoke

1. Pair Bluetooth Device:
   • Go to your tablet’s Bluetooth settings and look for the BPA 10 speaker.
   • Pair your device when you hear the confirmation sound.
2. Connect Receiver to Speaker:
   • Use the 1/4" cable to connect the receiver to the speaker.
   • Increase the MP3 volume on the receiver to hear the music from your tablet.
3. Test the Microphones:
   • Raise the volume for both microphones on the receiver.
   • You can now search for karaoke songs on YouTube or a similar app on your tablet and start singing along with the music.

8. Using the Mixer for Karaoke

1. Bluetooth Connection:
   • Activate Bluetooth mode on the mixer.
   • Go into the Bluetooth settings on your tablet and connect to the Rock Mix 10 FX mixer.
2. Setting Up Microphones on the Mixer:
   • Connect XLR outputs on the receiver to separate channels on the mixer (e.g., Channel 1 for microphone A and Channel 2 for microphone B).
   • Adjust the gain and level knobs on both channels for proper sound.
3. Testing the Setup:
   • After setting the volume, you can test the microphones to make sure they are working.
4. Use the Bluetooth Control Knob:
   • Adjust the Bluetooth knob on the mixer to control the volume of the music coming from the tablet.

Conclusion

Setting up the Rockville RWM-ICE wireless microphone system is easy and versatile. Whether you're using powered speakers or connecting to a mixer for advanced control, the process ensures clear sound and reliable performance for your karaoke or performance needs.