Skip to main content

WB65KLED Owner's Manual

Keith Harris

6.5˝ Wakeboard Tower Speakers w/Built-in LEDs

 

Wiring

  1. Amplified Audio Input Positive + (red)
  2. Amplified Audio Input Negative – (black)
  3. +12V LED Power (white)
  4. – LED Power Ground (blue)
  5. LED Power Connect
  • Connect the speaker positive (1) and negative wires (2) to the corresponding output terminals on the amplifier or receiver.
  • Connect the LED power connect cables (5) as shown below.
  • Connect the LED power wire (3) to the +12V (positive) terminal on your amplifier or receiver.
  • Connect the LED ground wire (4) to the ground (negative) terminal on your amplifier or receiver. This will allow you to bypass the battery, which makes the installation much easier.
Line drawing illustration of two pod speakers facing each other horizontally with their respective wiring setups labeled using numbered black circles: Left Speaker Wiring: 1: Red wire 2: Black wire 3: Grey wire 4: Blue wire Right Speaker Wiring: 1: Red wire 2: Black wire Interconnect Cable: 5: A quick-connect plug joining a cable coming out of the left speaker to a cable coming out of the right speaker.

 

360° Rotation Function

  1. Use an Allen wrench to loosen the rotation adjustment screw.Line drawing showing a black arrow pointing to an Allen socket head bolt seated inside the center recess of a curved mounting clamp base.
     
  2. Rotate the lower mounting bracket to the desired position.Line drawing showing a curved mounting clamp base being rotated relative to its underlying mount, with a large circular arrow indicating rotation.
     
  3. Tighten the rotation adjustment screw. Do not overtighten.mounting clamp.
     

Mounting Bracket

Bracket expands from 1.75˝ to 2.5˝ to fit a variety of wakeboard tower tube diameters. When making adjustments, use an Allen wrench to loosen and tighten the screws.

Line drawing of two mounting clamps connected by a double-headed arrow, showing an oval rubber insert setup on the left versus a circular rubber insert setup on the right.

 

Overview: A line drawing depicting a bullet-style pod speaker clamped onto a cylindrical bar, with text callouts and arrows labeling the assembly hardware from top to bottom. Labeled Components: Upper mounting bracket: The top curved piece of the clamp resting over the horizontal bar. Mounting screws: The fastners securing the top clamp to the lower assembly. Lower mounting bracket: The bottom curved section supporting the underside of the horizontal bar. 360° rotation point: The swiveling joint connecting the lower clamp to the mounting base. Mounting bracket base: The base plate secured to the top housing of the pod speaker.

 

Remote Control Features/LED Operation

1. Turn-On/Standby: Turn on LEDs or switch to standby mode. The speaker will remember the last used LED mode.

2/9. Dynamic Mode: Use to switch to dynamic mode from static color mode or to switch between dynamic modes.

3/10. Dynamic Mode Speed: Use to adjust dynamic mode speed. If the unit is in static mode, pressing either of these buttons will activate dynamic mode.

4/5. Static Color Adjust: Use to switch between static colors. If the unit is in dynamic mode, pressing either of these buttons will activate static mode.

6. Direct Color Select: Use to select preset static colors.

7/8. Brightness Adjust: Use these buttons to adjust brightness while in static mode. Pressing these buttons while the unit is in dynamic mode will switch it to static mode.

11. Demo Mode: Press this button to activate demo mode. While in demo mode, the unit will loop through 17 dynamic modes, repeating each mode 3 times.

Please Note: Be sure to remove the plastic cover from the battery compartment. The remote uses a 3 volt CR2025 battery (included). When replacing the battery, be sure to use one of the same type.

Overview: Front view of a white, handheld RF Wireless remote control featuring black, white, red, and colored circular buttons labeled with numbered black badges from 1 to 11. Numbered Button Layout: 1: Red power icon button at the top-left. 2: MODE + button at the top center of the cross directional pad. 3: SPEED – button on the left of the cross pad. 4: COLOR + button. 5: COLOR – button. 6: A outlined section at the bottom containing seven solid color preset buttons—a white button in the center top row, red, green, and dark blue in the middle row, and yellow, teal, and pink in the bottom row. 7: BRIGHT – button. 8: BRIGHT + button. 9: MODE – button at the bottom center of the cross directional pad. 10: SPEED + button on the right of the cross pad. 11: DEMO button in the center of the cross directional pad. "RF Wireless" text with a red Wi-Fi icon printed at the bottom center.

 

Features

  • Peak power handling per speaker: 300 Watts
  • RMS power handling per speaker: 150 Watts
  • Frequency response: 500Hz – 20KHz
  • Sound pressure level: 90dB
  • Impedance: 4 Ohms
  • Full function remote controls LED functions
  • Multi-color LEDs (blue, red, green, yellow, pink, purple, and white) with 20 static colors
  • 22 Dynamic modes
  • Steel enclosure
  • Aluminum mounting bracket
  • Quick and easy speaker angle adjustment
  • Bracket rotates 360°
  • 1˝ titanium dome tweeter
  • Fully marinized against salt & fresh water conditions
  • Completely resistant to water, rust, and UV rays
  • Polypropylene mica injected cone with rubber surround
  • 15oz high density magnet
  • 1˝ voice coil • CE and RoHS certified
  • These wakeboard speakers fit bars ranging from 1.75˝ – 2.5˝
  • Dimensions per speaker (H x W x D): 7.8˝ x 7.8˝ x 11.8˝
  • Weight per speaker: 5.3 lbs.
  • Available Colors: Polished Silver and Black

Comments

0 comments

Please sign in to leave a comment.

Powered by Zendesk