HP65S-8 BLACK: How To Set Up Home Theater Speakers

Introduction

Setting up your HP65S 8 Black speakers for optimal sound requires a few simple steps. Whether you're mounting the speakers on the wall or connecting them to a receiver, this guide will take you through the entire process. Follow these steps for the best results.

1. Unbox Your HP65S 8 Black Speakers

Your package should include the following:

• 2 HP65S 8 Black Speakers
• 2 Mounting Brackets
• 4 Knobs (2 per speaker)
• Foam Pads for extra protection and padding
• 2 Sets of Speaker Wire for connecting to your receiver
• Mounting Hardware for wall installation

2. Mounting Your Speakers on the Wall

Choosing the Right Spot

1. Check for Studs: If you plan to mount the speakers onto drywall, you need to decide where to place them. If there's a stud behind the drywall, you won't need anchors. Use a stud finder to locate the studs, typically spaced 16 or 24 inches apart.
2. No Studs?: If there are no studs, use anchors to secure the speakers.

Marking the Holes

1. Mounting Bracket Alignment: Take the mounting bracket and align it with the spot on the wall where you want the speaker. The bracket should have a backward "L" shape for proper placement.
2. Mark the Holes: Use a pen or pencil to mark where the holes should go. Make marks on the top line of the bracket to ensure proper speaker placement.

Drilling and Installing Anchors

1. Drill Holes: Use a ¼ inch drill bit to drill holes where you marked the spots.
2. Install Anchors: Insert the anchors into the holes. If they don't fit, lightly tap them in with a hammer.

Securing the Bracket

1. Mount the Bracket: Use the provided screws to attach the mounting bracket to the wall. Tighten securely with a drill.

3. Mounting the Speaker to the Bracket

Using the Knobs

1. Prepare the Speaker: Place the speaker on the mounting bracket. Align the top and bottom holes of the speaker with the bracket's corresponding holes.
2. Attach the Knobs: Insert the knobs through the holes and tighten them to secure the speaker to the bracket.
3. Swivel Feature: If you haven't tightened the knobs fully, the speaker will swivel for the perfect angle. Tighten the knobs to lock the speaker in place.

4. Wiring the Speakers to the Receiver

Connecting the Speakers

1. Use the Provided Speaker Wires: Take the speaker wire and connect the positive (red) and negative (black) terminals on the back of the speaker.
2. Connect to the Receiver: Plug the other ends of the speaker wire into the corresponding terminals on your receiver.

Impedance Matching

• These HP65S 8 Black speakers are 4-ohm speakers. Make sure your receiver is 4-ohm compatible.
• If you plan to wire multiple speakers, parallel wiring is an option to achieve a 4-ohm load on your 4-ohm receiver. Ensure you do not wire more than one speaker per channel unless you're using parallel wiring.

5. Optional: Parallel Wiring for Multiple Speakers

If you're wiring two speakers per channel:

1. Connect Speaker Wires to Both Speakers: Start by wiring the first speaker to your receiver. Then wire the second speaker to the first one, connecting the positive to positive and negative to negative.
2. Combine the Wires: Twist the red wires together, then twist the black wires together.
3. Connect to the Receiver: Finally, connect the other ends of the second speaker wire to the positive and negative terminals of one channel on the receiver.

6. Testing Your Setup

• Play Some Music: After ensuring all wires are securely connected, turn on your receiver and test the speakers by playing music. Adjust volume and sound settings as needed.
• Check the Sound: The sound should be clear, balanced, and powerful. If you have multiple speakers connected in parallel, ensure they're all producing sound as expected.

7. Conclusion

Setting up your HP65S 8 Black speakers is a straightforward process. Whether you're mounting them on the wall or connecting them to a receiver, following these steps will ensure your setup is secure and optimized for the best sound.